S-200

TECHNICAL PRODUCT BULLETIN #B-56
USEPA, OIL PROGRAM CENTER
LISTING DATE: JULY 24, 2002
"S-200"
(a/k/a SHEENCLEAN, S-200C, BILGE CLEAR, S-200 OIL GONE, S-200 OIL CLEAN, OIL GONE EASY)

I. NAME, BRAND, OR TRADEMARK
S-200
(a/k/a SHEENCLEAN, S-200C, BILGE CLEAR, S-200 OIL GONE, S-200 OIL CLEAN, OIL GONE EASY)
Type of Product: Bioremediation Agent (Nutrient Additive)
II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT
International Environmental Products, LLC
Two Villanova Center
795 E. Lancaster Ave., Suite 280
Villanova, PA 19085
Phone: (610) 520-7665
Fax: (610) 520-7663
Email: info@iepusa.com
(Mr. Jim Lynn)
III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS
International Environmental Products, LLC
Two Villanova Center
795 E. Lancaster Ave., Suite 280
Villanova, PA 19085
Phone: (610) 520-7665
Fax: (610) 520-7663
Email: info@iepusa.com
(Mr. Jim Lynn)
IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION
1. Flammability:
Non-flammable.
2. Ventilation:
Ventilation of the work place is not necessary.
3. Skin and eye contact; protective clothing; treatment in case of contact:
In case of contact with skin or eyes, wash with plenty of water.
4.a. Maximum storage temperature: 132ºF
4.b. Minimum storage temperature: 32ºF
4.c. Optimum storage temperature range: 55ºF - 85ºF
4.d. Temperatures of phase separations: <32ºF and >140ºF
V. SHELF LIFE
The recommended shelf life of S-200 is 1½ years if kept in the unopened original container.
VI. RECOMMENDED APPLICATION PROCEDURE
1. Application Method:
S-200 is a light amber liquid, and as such can be sprayed with traditional liquid spraying equipment, such as pressurized sprayers or backpack sprayers.
2. Concentration/Application Rate:
The recommended application rate is approximately 10% by volume of the S-200 as compared to the hydrocarbon being remediated. In other words, use 1 pound of S-200 for every 10 pounds of hydrocarbon you are remediating.
For applications on soil contaminated below 1 foot, the soil is turned and the material is applied. This allows air to circulate and thereby maintains an aerobic condition.
On a surface application, the amount to use is approximately 0.1 to 1 pound of S-200 for every square yard of surface area. The amount sprayed is dependent on the amount of hydrocarbon on the surface you are spraying.
To remediate a sheen on water, the same application ratio for a surface application is used.
3. Conditions for Use:
S-200 is a bioremediation accelerator used for the remediation of hydrocarbon spills or leaks. It is a non-intrusive, cost effective remedy for the cleanup of these hydrocarbons. These hydrocarbons include but are not limited to gasoline, No. 2 to No. 6 diesel fuel, jet fuels, kerosene, lubricating oils, hydraulic oils, and crude oils.
VII. TOXICITY AND EFFECTIVENESS
a. Toxicity
Material Tested Species LC50 (ppm)
S-200 Menidia beryllina
Mysidopsis bahia
39.69 96-hr
21.33 48-hr
No. 2 Fuel Oil Menidia beryllina
Mysidopsis bahia
35.36 96-hr
35.36 48-hr
S-200 & No. 2 Fuel Oil (1:10) Menidia beryllina
Mysidopsis bahia
25.33 96-hr
17.67 48-hr
Reference Toxicant (SDS) Menidia beryllina
Mysidopsis bahia
NA 96-hr
22.96 48-hr

b. Effectiveness:
Bioremediation Agent Effectiveness Test (40 CFR 300.900), Federal Register September 15, 1994:

Summary Data Table:
DAYS PRODUCT
3 REPS/PROD
TOTAL MEAN
ALKANES (ppm)
RED%
28 DAYS
TOTAL MEAN
AROMATICS (ppm)
RED%
28 DAYS
0 CONTROL
S-200
27666
29333
0
0
5600
5666
0
0
7 CONTROL
S-200
21333
11000
0
0
4333
4400
0
0
28 CONTROL
S-200
18771
660
32
98
5597
5073
0.05
10.4


Results of Gravimetric Analysis:
Percentage (%) Decrease in Weight of Oil on Day 28
Control
-18.57%
Product (001)
27.82%
VIII. MICROBIOLOGICAL ANALYSIS
1. Listing of all microorganisms by species and percentages in the composition:
S-200 is a nutrient bioremediation accelerator and does not contain bacterial cultures or amendments. However, with the addition of S-200, the microbiological data shows a continued viability of microbial incubations over time.
2. Optimum pH, temperature, and salinity ranges for use of the additive:
pH: 7.0
Temperature: 86ºF
Salinity: Fresh to salt water
3. Minimum and maximum pH, temperature, and salinity levels below or above which the effectiveness of the additive is reduced to half its optimum capacity:
pH: 4.5 - 10.0
Temperature: 50ºF - 120ºF
Salinity: 0% - 10%
4. Special nutrient requirements:
NA
5. Test results regarding the determination of the presence of the following:
Salmonella: Negative
Fecal coliform: Negative
Shigella: Negative
Staphylococcus Coagulase positive: Negative
Beta hemolytic Streptococci: Negative
IX. PHYSICAL PROPERTIES
1. Flash Point: > 212ºF
2. Pour Point: 40ºF
3. Viscosity: 100cp @ 70ºF
4. Specific Gravity: 0.996
5. pH: 4.5
6. Surface Active Agents: NA
7. Solvents: NA
8. Additives: NA
9. Solubility in Water: Dispersable
X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS
S-200 does not contain any heavy metals, cyanide, or chlorinated hydrocarbons.

Top of Page